642-813 practice exam
2 posters
Page 1 of 1
642-813 practice exam
1. Company uses layer 3 switches in the Core of their network. Which method of Layer 3 switching uses a
forwarding information base (FIB)?
A.Topology-based switching
B. Demand-based switching
C. Route caching
D. Flow-based switching
E. None of the other alternatives apply
Answer:A
2. You need to design the VLAN scheme for the Company network. Which two statements are true about
best practices in VLAN design? (Select two)
A. Routing should occur at the access layer ifvoice VLANs are utilized. Otherwise, routing should occur at
the distribution layer.
B. Routing should always be performed at the distribution layer.
C. VLANs should be localized to a switch.
D. VLANs should be localized to a single switch unlessvoice VLANs are being utilized.
E. Routing should not be performed between VLANs located on separate switches.
Answer: BC
3. Refer to the exhibit. On the basis of the information provided in the exhibit, which two sets of procedures
are best practices for Layer 2 and 3 failover alignment? (Choose two.)
A. Configure the D-SW1 switch as the active HSRProuter and the STP root for all VLANs.
Configure the D-SW2 switch as the standby HSRP router and backup STP root for all VLANs.
B. Configure the D-SW1 switch as the standby HSRP router and the STP root for VLANs 11 and 110.
Configure the D-SW2 switch as the standby HSRP router and the STP root for VLANs 12 and 120.
C. Configure the D-SW1 switch as the active HSRProuter and the STP root for VLANs 11 and 110.
Configure the D-SW2 switch as the active HSRP router and the STP root for VLANs 12 and 120.
D. Configure the D-SW2 switch as the active HSRProuter and the STP root for all VLANs.
Configure the D-SW1 switch as the standby HSRP router and backup STP root for all VLANs.
E. Configure the D-SW1 switch as the active HSRProuter and the backup STP root for VLANs 11 and 110.
Configure the D-SW2 switch as the active HSRP router and the backup STP root for VLANs 12 and 120.
F. Configure the D-SW1 switch as the standby HSRP router and the backup STP root for VLANs 12a nd
120.
Configure the D-SW2 switch as the standby HSRP router and the backup STProot for VLANs 11 and 110.
Answer: CF
Test1pass offers free Testing Engine for Cisco 642-813 exam.You can check out the interface, question quality and usability of our practice exams before you decide to buy it.These Exam Resources updates are supplied free of charge to Test1pass customers. If you have any question about Test1pass 642-813 practice test, please feel free to contact us at any time.
forwarding information base (FIB)?
A.Topology-based switching
B. Demand-based switching
C. Route caching
D. Flow-based switching
E. None of the other alternatives apply
Answer:A
2. You need to design the VLAN scheme for the Company network. Which two statements are true about
best practices in VLAN design? (Select two)
A. Routing should occur at the access layer ifvoice VLANs are utilized. Otherwise, routing should occur at
the distribution layer.
B. Routing should always be performed at the distribution layer.
C. VLANs should be localized to a switch.
D. VLANs should be localized to a single switch unlessvoice VLANs are being utilized.
E. Routing should not be performed between VLANs located on separate switches.
Answer: BC
3. Refer to the exhibit. On the basis of the information provided in the exhibit, which two sets of procedures
are best practices for Layer 2 and 3 failover alignment? (Choose two.)
A. Configure the D-SW1 switch as the active HSRProuter and the STP root for all VLANs.
Configure the D-SW2 switch as the standby HSRP router and backup STP root for all VLANs.
B. Configure the D-SW1 switch as the standby HSRP router and the STP root for VLANs 11 and 110.
Configure the D-SW2 switch as the standby HSRP router and the STP root for VLANs 12 and 120.
C. Configure the D-SW1 switch as the active HSRProuter and the STP root for VLANs 11 and 110.
Configure the D-SW2 switch as the active HSRP router and the STP root for VLANs 12 and 120.
D. Configure the D-SW2 switch as the active HSRProuter and the STP root for all VLANs.
Configure the D-SW1 switch as the standby HSRP router and backup STP root for all VLANs.
E. Configure the D-SW1 switch as the active HSRProuter and the backup STP root for VLANs 11 and 110.
Configure the D-SW2 switch as the active HSRP router and the backup STP root for VLANs 12 and 120.
F. Configure the D-SW1 switch as the standby HSRP router and the backup STP root for VLANs 12a nd
120.
Configure the D-SW2 switch as the standby HSRP router and the backup STProot for VLANs 11 and 110.
Answer: CF
Test1pass offers free Testing Engine for Cisco 642-813 exam.You can check out the interface, question quality and usability of our practice exams before you decide to buy it.These Exam Resources updates are supplied free of charge to Test1pass customers. If you have any question about Test1pass 642-813 practice test, please feel free to contact us at any time.
qetyu- Posts : 1
Join date : 2011-03-01
Re: 642-813 practice exam
You provide a very good message,Test1pass's exam questions have high accuracy and it's service is very good!
lgfhdty- Posts : 1
Join date : 2011-02-13
Similar topics
» Ourexam latest 000-197 practice exam
» HP0-M31 practice test
» Ourexam HP HP0-S27 practice tests
» Ourexam HP0-S28 Practice Exams
» Ourexam 000-M80 practice questions
» HP0-M31 practice test
» Ourexam HP HP0-S27 practice tests
» Ourexam HP0-S28 Practice Exams
» Ourexam 000-M80 practice questions
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
|
|